In the face of rapidly depleted fresh water supplies, the industrial sector is learning that reducing water usage and increasing reuse is an essential ingredient of productivity and profitability today. This is increasingly true in countries such as the U.S., where water usage for industrial purposes is 46 percent of all water consumption, says Dr. Peter Glieck, President of the Pacific Institute for environmental studies.
Today’s manufacturers and fabricators are now realizing that they are major stakeholders in this global water conservation effort and that water conservation saves cost. As such, giant conglomerates like Ford Motor Company (Dearborn, MI) and Parker Hannifin Corporation (Cleveland, OH), to global heat-treating specialists like Bodycote (Rochester, NY), are beginning to focus on process water reuse to not only conserve water, but to also improve process uptime and product quality, along with reducing exorbitant disposal and maintenance costs. To do this they are taking actions such as incorporating advanced separation technology, addressing pollution like oil, grease or dirt, to increase the life of precious production fluids like cleaner solutions and coolants. So, how does this affect an industrial part washer?
New Realities in Aqueous Separation
Automotive manufacturers and metal fabricators, for example, are using a new and highly efficient technology—dynamic oil separation—to continuously remove process oils and even minute contaminants from an aqueous cleaning solution, while being used with no process interruptions. Traditional mechanical separation methods are based on one of two principles: (1) gravity separation, in combination with weir skimmers and tank overflow, or
(2) adhesion, with hoses, wheel/disks or belt skimmers used to adhere oil in order to lift it
from the surface of bath water. Both methods are problematic, particularly in high-volume
production settings where delays to change or maintain aqueous baths involve downtime.
For instance, adhesion separation often allows dirt to settle through surface oil and cycle back into the bath water, leading to dirty parts and requiring frequent solution change. The adhesion method also draws up and removes cleaning agents along with water and oils, creating “wet” oil and adding to oil disposal costs. The overflow (decanting) method wastes vast amounts of coolant or cleaner from the bath, which is a waste of costly resources.
Another method, which uses honeycomb-like traps or plates called “coalescing media” to separate and capture oil and contaminants, has proved to be inefficient and maintenance intensive due to its sensitivity to dirt.
Instead, dynamic separation technology operates on a different principle—Bernoulli’s Effect, the phenomenon whereby increased stream velocity in a fluid results in internal pressure reduction. The Bernoulli Effect is probably best known as the principle that creates the “lift” of aircraft wings. Dynamic separation uses fluid pressure differential to enable the separation of liquids of differing specific gravities. This technology was developed by Aqueous Recovery Resources (ARR) (Bedford Hill, NY) and is incorporated in its Suparator® systems specifically for this type of application.
This unique technology removes oil so effectively, that lots of dirt and other foreign matter are separated with the oil. Elimination of these contaminants warrants a much cleaner process and cleaner parts, translating to better quality products and less rejects. Dynamic separation also extends bath life, providing significant savings in detergents. Bath changes are greatly reduced, vast quantities of water are conserved, oils are more efficiently recycled and far smaller volumes of cleaners and coolants have to be disposed of.
Ford Dearborn—Pressing for Perfection
At Ford Motor Company’s Dearborn, MI plant, a giant, 2,600-ton Schuler press using up to 300 tons of dies turns 700,000 pounds of steel per day into doors for their best-selling Ford F150 pickup trucks. At the press area, stacks of steel “blanks” arrive, each blank coated with a thin film of mill oil to preserve the metal against corrosion. The steel blanks have to be washed to get rid of the oil and any dirt or other foreign matter prior to being stamped. “These oiled blanks attract dirt like a magnet,” says Ed Spencer, controls engineer at the Ford Dearborn stamping operation. “As a result, the blanks have to be washed thoroughly.We don’t want that oil, which may have dirt in it, to get into the die. So, we spray wash it with a detergent solution pumped up from a huge tank downstairs.”
If even one piece of dirt “birdshot” remains on a blank when the giant press hits it, the finished piece will have a dimple on it that ruins the door. At the rate the Dearborn plant are stamping the doors—900 pieces an hour—if a dirt problem is not identified quickly, the result could be the scrapping of a lot of metal in a very short time. “We have very tight demand,” Spencer explains. “We have an assembly department downstairs that puts the inner and outer door panels together and then we ship it off to assembly. If we remain shut down because of dirt issues with the cleaning solution, we have problems: manpower and productivity loss, and wasted parts.”
Recognizing the need for an efficient and reliable separation technology to maintain a clean process, the Ford stamping operation installed a Suparator unit from Aqueous Recovery Resources (Bedford Hill, NY) in 2006. In addition to meeting high Ford quality standards, which was essential, Spencer recognized that a truly effective oil separation technology would help maximize the uptime of the critical Schuler press that had to meet extraordinarily high volume requirements.
Now, after the dirt and oil are washed off the blanks, the cleaner returns to the holding tank where the Suparator removes fluid from the surface. Any oil in this concentrated stream, with any entrained dirt, is separated from the fluid continuously and without water or detergent. “In the past, we used a centrifuge system that spun and tried to get the heavy particulate out of the solution that way. But that was a maintenance nightmare,” Spencer says. “We tried to remove the oil with a hose-type skimmer, a plastic tube that went around in a circle, and the oil would cling to it, supposedly. But it never really worked.
“When we saw the Suparator technology, I thought we should test it,” Spencer continues. “And it works about 100 times better than the other system. We get only a small amount of water with the oil, but it is about 100 times more efficient than the other system. The key is it takes out the fine dirt particles better than the centrifuge ever did.” Spencer adds that although the policy of his operation is to change the cleaner every two weeks, it stays clean enough to extend its use to at least two months. That pays off in added productivity, especially considering that there is no backup equipment for the giant Schuler press. “We’re realizing our major savings on quality and availability,” he says. “Uptime is now averaging up to 95 percent, which is excellent for the stamping industry. We also have less wasted materials and get extended cleaner life. Obviously, that adds up to a lot.”
Extending resources at Parker-Hannifin
At the Hydraulic Pump/Motor Division of Parker Hannifin Corporation, a Lindberg washer incorporated intentional overflow of the cleaning bath to remove quench oil from heat-treated parts. This method resulted in the loss of cleaner and “excessive volumes” of water being added to the plant’s effluent, according to Larry McCracken, plant engineer.
To reduce the costs resulting from those cleaning and disposal problems, the washer was modified to eliminate the need to continuously overflow the bath. However, some system was needed to control the oil concentrations in the bath. “Initially, a belt-type skimmer was tried, but was unsuccessful,” McCracken says. “So, a Suparator unit was tried on ARR’s 30-day Trial Program. Approximately 10 gallons of quench oil is removed from the bath daily. This result has greatly reduced operating costs as well as our getting cleaner parts from the washer.”
Cost savings included a reduction in water consumption from 19,080 gallons per month to only 3,480 per month. Chemical losses, previously recorded at 298 gallons per month, were reduced by 244 gallons—a savings of almost 82 percent. The monthly cost of water disposal was reduced by approximately 80 percent, and the monthly cost of chemicals reduced by more than 80 percent. The total annual savings has been at least $101,184.
Multiple Cost Savings
Blaine Timmerman of Bodycote, the world’s largest provider of metallurgical testing and thermal processing services, says that his Rochester NY’s heat-treating facility has experienced multiple payoffs from the use of dynamic separation.
In high-volume production operations such as Bodycote’s, downtime or quality rejects resulting from inferior separation methods is costly and causes weekly or even daily maintenance problems such as dirty bath water and frequent bath changes. Such problems can lead to scrapped products as well as falling behind JIT demands.
Timmerman explains that in the past, his heat-treating process tended to create a rag layer between the oil and water in the dunk/spray washer. “We would get this nasty in between layer that was an emulsification of water in oil,” he says. “It didn’t completely separate into either the oil or water. It tended to stay right there in the middle, sandwiched between the water and oil. And that hindered oil separation because the emulsified layer would roll down the skimmer rope or plate back into the water and stay there.” The result was more frequent bath changes and downtime. “I had tried just about every oil separation technology,” says Timmerman, “Our operation and our customers are very demanding, and conventional oil separators just haven’t met our needs.”
After using a variety of separation devices, including disks, belts, mops and plates, Timmerman heard of a new dynamic separator technology, the Suparator, which removes virtually all oil, the oily emulsion and oil-suspended particulates from aqueous media, even at very low concentrations. The Suparator system removes oil-entrained solids and particulates, which means that they do not have time to settle through the oil into the water. This also significantly improves product quality, maintenance intervals and associated downtime.
In addition, the dynamic separator technology saves Timmerman’s Bodycote operation on oil disposal costs. “We used to have to pay a penalty to dispose of oil with high water content,” says Timmerman. “In 2002, relatively ‘dry’ oil disposal cost was approximately 15 cents a gallon. But because of the water drag-out of our old oil separators, we were getting wet oil. If the oil had more than 10 percent water, which was often the case, we had to pay around $1.05 per gallon—a very significant difference.” In 2007, the penalty price for wet oil would be much higher.
According to Timmerman, today, in addition to eliminating the rag (emulsified) layer and the water drag-out, the dynamic separation technology has cut oil disposal costs as well as increasing the reuse of their bath water several times over.
Article From: Process Cleaning